Valve Manufacturer in India

Industrial Valves Manufacturer, Supplier & Exporter in India

Amardeep Steel Centre LLP has built its valve business the same way it built its pipe and fittings trade: by stocking deep and shipping fast. Out of Mumbai, the company manufactures, stocks, supplies and exports Gate, Globe, Check, Ball, Butterfly and Sluice valves, along with steam traps and strainers, in Stainless Steel, Carbon Steel, Alloy Steel, Duplex, Monel, Inconel and Hastelloy. Process plants in more than 60 countries now source from this range.

Sizes run from 1/2" (15 NB) right up to 48" (1200 NB). On the pressure side, the catalogue spans ANSI Class 150 through 2500 LBS and DIN PN10 through PN40, built to API 6D, API 600, ASME B16.34 and IS 14846.

Valve Types We Supply

• Gate Valves
• Globe Valves
• Check Valves
• Ball Valves
• Butterfly Valves
• Steam Traps & Strainers
• Sluice Valves & Pressure Reducing Valves

Industrial Valve Standards, Certifications & Pressure Classes

Valve Manufacturing & Quality Testing Process

Most valve bodies and trims in this range start life either as a casting (the route used for Gate, Globe, Check, Ball and Butterfly bodies) or as a forging, reserved for smaller, higher-pressure designs where grain flow matters more than casting economics. From there, every valve goes through the same sequence: raw material checks, precision CNC machining of the bore, seats and stem, assembly, and pressure testing before it ships.

• Raw material verification and chemical/mechanical testing of body, trim and seat materials
• Precision CNC machining of body bore, seats and stem for accurate sealing and smooth operation
• Hydrostatic shell test to confirm pressure-boundary integrity, and a seat leakage test run to API 598
• Functional testing of open/close operation, actuator interface and by-pass arrangements where fitted
• Final dimensional check, marking (size, class, material grade, heat number) and EN 10204 mill test certification

Gate Valves

A gate valve does its job with a flat or wedge-shaped gate that lifts entirely clear of the bore when open, so pressure drop across an open gate valve is about as low as it gets. That's also its limit: the same full-bore clearance that makes it efficient when open makes it a poor choice for throttling, so these are specified for on-off duty, not flow control. Amardeep supplies both Hand Wheel Operated and Gear Operated versions, and the following are available on request:

• Solid or flexible wedge design
• Special flange facings (large/small male-female, ring-joint face) for applications that call for them
• A matching electric actuator where the valve needs to run remotely or on automation
• By-pass arrangement, position indicator and extension stem, with or without a floor stand
• Pressure-seal bonnet design on request

Globe Valves

Where a gate valve is built for clearance, a globe valve is built for control. Flow takes an S-shaped path through the body, past a disc and seat, the geometry that gives globe valves their throttling precision and a tighter shutoff than a gate valve can manage, at the cost of a permanent pressure drop even when the valve is wide open. Both Hand Wheel Operated and Gear Operated versions are available, in:

• Steel bolted bonnet
• Steel pressure-seal bonnet
• Cryogenic service construction
• Cast iron O, S & Y pattern
• Bellow seal, for a zero-leakage stem
• Chlorine service construction

Check Valves

Check valves have one job: let flow move one way and stop it from reversing, automatically, with no operator or actuator involved. The range covers Swing Check, Lift Type, Single Plate Wafer and Dual Plate Wafer designs, built as:

• Steel bolted cover, swing type
• Steel pressure-seal cover, swing type
• Wafer type
• Dual plate type
• Non-slam type
• Flap type

Ball Valves

A quarter turn of the handle rotates the bored ball in and out of the flow path, which is why ball valves are the go-to choice wherever tight shutoff and fast operation both matter, and, in full-bore form, the flow path is barely restricted at all when open. The lineup runs from 1-Piece through 2-Piece and 3-Piece (reduced bore, full bore and full-jacketed variants) up to 3-Way/4-Way IC ball valves, plus several purpose-built designs:

• 2x2 Sandwich Ball Valve: body/ball in CF8 (SS304), CF3 (SS304L), CF8M (SS316), CF3M (SS316L) or cast steel WCB; PTFE seat/seal; Class 150#/300#; wafer end to ANSI B16.5
• 2/2 and 3/2 High Pressure Ball Valves: forged CS/SS304/SS316 body; Viton O-ring; rated to 80°C as standard, higher on request; suited to air, water, oil and gas media
• 3-Piece High Pressure Ball Valve: body to ASTM A216 Gr. WCB / A351 Gr. CF8/CF8M; AISI 304/316 ball; Class 800#/900#
• Flush Bottom Ball Valve: same material range as the 3-piece design, built for tank and vessel bottom-outlet service

Butterfly Valves

A butterfly valve trades a little pressure drop for a lot of practicality: the disc stays in the bore even fully open, but because the whole assembly is thinner and lighter than an equivalent gate or ball valve, it's the natural choice once pipe diameters get large. The range covers Wafer Type, Offset Disc, Lugged Type, Pharma, Double Flanged Handle and Spherical Disc designs, across Models 12/12L, 44/44L, 98 Hygiene, 81, 85F, 91/91L (High-Performance Double Offset) and 93/93L (High-Performance Triple Offset), with material options including:

• Pharma Butterfly Valve: CF8/CF8M/CF3M body and ball; silicone gland seal/seat; rated to 6 bar/vacuum; wafer end to ANSI 150#
• Double Flanged Handle Butterfly Valve: Cast Iron/Ductile Iron/SG Iron/Cast Steel/SS304/SS316 body; PTFE gland seal; EPDM/Nitrile/Hypalon/Viton seat; PN10/PN16
• Spherical Disc Butterfly Valve: same body material range; PTFE gland seal; EPDM/Nitrile/PTFE seat; PN10/PN16/PN25/150#/300#

Steam Traps & Strainers 

The Float Type Steam Trap (FT-10) is built around a stainless steel body for long service life with minimal maintenance; a self-aligning valve and water seal stop live steam escaping, a modulating orifice keeps condensate draining continuously, an integral air vent speeds up start-up, and the float itself is designed to survive water-hammer impact rather than fail under it.

Y-Type and T-Type Strainers take their name from their body shape and handle coarse-to-fine filtration ahead of valves, pumps and instruments; bodies are typically cast iron or cast steel with flanged or socket-weld ends, and the filter element itself is stainless steel perforated sheet or wire mesh. For applications that can't tolerate a shutdown to clean a strainer, Duplex (twin-basket) strainers pair two three-way ball valves on a common handle so flow switches to a standby basket while the other is cleaned (available up to 48" NB and down to 5 micron filtration).

Sluice Valves & Pressure Reducing Valves

Sluice Valves, built to IS 14846 in Rising and Non-Rising Spindle configurations, are rated for clear water service up to 5,000 ppm turbidity and 45°C as standard (up to 180°C on special design), with position indicator, by-pass arrangement, back-seat repacking, spur/bevel/worm gear operation, thrust bearing arrangement and electric actuation all available as options.

The Drum Type Pressure Reducing Valve uses a Cast Iron/Cast Steel/SS304/SS316 body and piston with a BUNA-N seat, covering 1-7 kg/cm² and 4-12 kg/cm² reducing ranges up to an 18 kg/cm² maximum inlet pressure, with a flanged 150# end connection.

Industrial Valves Applications & Industries We Serve

These valves move through Chemicals, Petrochemicals, Oil & Natural Gas, Fertilizers, Sugar Mills & Distilleries, Cement, Ship Building, Paper, Pumps & Automation, Paints and general Steel plants; three sectors in particular account for most of the volume:

• Oil, Gas & Power: Gate, globe, ball and check valves for pipelines, refineries, boilers and power generation, mostly in Carbon Steel, Alloy Steel and Duplex
• Marine, Water & Wastewater: Sluice valves, butterfly valves and strainers for water supply, desalination and wastewater treatment, with Monel and Cu-Ni options where seawater service demands it
• Pharmaceutical & Food Processing: Hygienic Pharma butterfly valves and stainless steel ball valves for sterile process piping

Valve Exporter — Countries We Serve 

Regular export destinations include Kuwait, UAE, UK, Iran, Iraq, Qatar, Bahrain, Oman, Yemen, Lebanon, Jordan, Saudi Arabia, Malaysia, Indonesia, Singapore, Australia, New Zealand, USA, Canada, Mexico, Brazil, the Netherlands, Germany, Italy, Spain, Poland, South Africa, Turkey, Egypt and Sri Lanka, part of a footprint now covering 60+ countries.

Why Choose Us as Your Valve Manufacturer & Supplier in India

• A genuinely broad range (nine valve families and their specialised sub-types) from a single stockist, so one enquiry can cover a whole project's valve list
• Material-of-construction options matched against your process fluid and temperature, not a one-size-fits-all default
• EN 10204 3.1/3.2 mill test certification with full heat-to-test traceability
• Regular export shipments across the Middle East, Africa, Europe, the Americas and South-East Asia