
Low Fin Tube Manufacturer, Supplier & Exporter in India
Condenser Low Fin • Integral • Turbo Chill • Internal Low Fin • Micro Fin
In a shell-and-tube exchanger, the side with the poorer heat transfer sets the pace for the whole unit. Often that is the shell side, where a vapour is condensing or an oil is cooling slowly. Adding fins there helps, but high fins are too big for standard tube sheets and baffles. Low fin tubes solve this from inside the tube’s own wall.
Rotating rollers press the wall of a plain tube into a fine helical fin, usually under 1.5 mm high, with 19 to 26 fins per inch. Nothing is added or welded, so the fin can never work loose. The finned section stays within the original outside diameter, and the tube ends are left plain so they can be rolled into the tube sheet like any other tube. The result is about 2.5 to 3 times the outside surface in the same space.
Amardeep Steel Centre supplies low fin tubes in copper, copper-nickel, brass, carbon steel, stainless steel, duplex and titanium, straight or U-bent. Every order ships with an EN 10204 3.1 mill test certificate.
What are Low Fin Tubes?
A low fin tube is a single-piece heat exchanger tube whose outer wall has been cold rolled into short, closely spaced helical fins. Because the fin and tube are one piece of metal, heat passes straight through with no contact gap. Low fin tubes are used where a liquid or condensing vapour is on the shell side, such as condensers, chillers, oil coolers and reboilers.
Low Fin Tube Types
Condenser low fin
- What sets it apart
- Standard external low fin, typically 19 or 26 FPI
- Best for
- Steam, refrigerant and ammonia condensers
- Type page
- Condenser low fin tubes
Integral finned
- What sets it apart
- Fins formed from the tube wall in one piece; general term for the product family
- Best for
- Shell-and-tube coolers and heaters
- Type page
- Integral finned tubes
Turbo chill
- What sets it apart
- Enhanced low fin with a modified fin profile for boiling and condensing refrigerants
- Best for
- Chillers and refrigeration evaporators
- Type page
- Turbo chill fin tubes
Internal low fin
- What sets it apart
- Fins or grooves formed on the inside of the tube
- Best for
- Improving the tube-side coefficient
- Type page
- Internal low fin tubes
Micro fin
- What sets it apart
- Very fine internal grooves in small-diameter copper tube
- Best for
- Air-conditioning and refrigeration coils
- Type page
- Micro fin tubes
Low Fin Tubes vs Plain Tubes
| Plain tube | Low fin tube | |
|---|---|---|
|
Outside surface |
1× |
About 2.5–3× |
|
Fits standard tube sheet and baffles |
Yes |
Yes (plain ends at original OD) |
|
Condensing performance |
Condensate forms a film |
Fins shed condensate as droplets, so more heat transfer |
|
Fin bond |
– |
Integral; cannot loosen |
|
Exchanger size for the same duty |
Larger |
Smaller, or more capacity in the same shell |
Low Fin Tube Standards and Materials
| Standard | Material | Our material page |
|---|---|---|
|
ASTM B359 / ASME SB359 |
Copper and copper alloy (copper, Cu-Ni 90/10 and 70/30, admiralty and aluminium brass) |
|
|
ASTM A498 |
Carbon and low-alloy steel (A179, A210, A334) |
|
|
ASTM A1012 |
Stainless steel and duplex (A213, A789) |
|
|
ASTM B891 |
Titanium and titanium alloy (B338) |
– |
Carbon steel low fin tubes are used for ammonia condensers, where copper alloys cannot be used.
Typical Low Fin Specifications
| Parameter | Typical range |
|---|---|
|
Fins per inch |
19 and 26 FPI (others to order) |
|
Fin height |
Up to about 1.5 mm |
|
Plain-end OD |
Matches original tube OD |
|
Forms |
Straight and U-bent |
|
Testing |
Hydrostatic or pneumatic, eddy current |
Applications of Low Fin Tubes
- Steam, refrigerant and ammonia condensers
- Chillers and refrigeration evaporators
- Lube oil and process coolers
- Reboilers and feed heaters
- Power plant and desalination exchangers
- Retrofits to raise the capacity of existing shells
Send us the material, OD × wall, fins per inch, plain-end lengths, overall length, U-bend radius if needed and quantity for a quote.
FAQs – Low Fin Tubes
What is a low fin tube?
A tube with short fins, usually under 1.5 mm high, rolled out of its own wall. Because the fins are part of the tube, there is no joint to loosen, and the finned section keeps the same outside diameter as the plain ends.
How are low fins formed?
The plain tube is passed through rotating roller discs that cold-form the wall into a helical fin. No material is added or cut away.
What is the advantage of low fin tubes over plain tubes?
They give about 2.5 to 3 times the outside surface area in the same tube diameter, so fewer tubes or a smaller exchanger can do the same duty. They also shed condensate faster in condensers.
Can low fin tubes replace plain tubes in an existing exchanger?
Yes. The plain ends match the original outside diameter, so the tubes fit the same tube sheet holes and baffles. This makes low fin tubes a common retrofit to raise capacity without a new shell.
