
Helical Fin Tube Manufacturer, Supplier & Exporter in India
Solid • Serrated • High Fin • Anti-Corrosive • Wire Wound • Crimped
Hot exhaust gas from a turbine or furnace carries a great deal of heat, but gas is a poor conductor. A bare tube placed in that stream recovers only a fraction of the energy, because there is too little surface for the gas to touch. Winding a fin around the tube in a continuous spiral changes that. The fin can add eight to ten times the outer surface area, and the spiral shape stirs the gas so it gives up more heat as it passes.
How the fin is made and fixed decides where the tube can work. Welded steel fins survive the high temperatures of heat recovery steam generators and fired heaters. Tension-wound aluminium or copper fins suit air coolers and HVAC coils, where light weight and conductivity matter more than heat resistance. Serrated, crimped and wire forms trade a little pressure drop for extra turbulence and heat transfer.
Amardeep Steel Centre supplies helical fin tubes in six designs on carbon steel, alloy steel, stainless steel and copper-alloy base tubes. Every order ships with an EN 10204 3.1 mill test certificate.
What are Helical Finned Tubes?
A helical finned tube is a heat exchanger tube with a metal fin wound around its outer surface in a continuous spiral. The base tube carries the hot or cold fluid, and the fin carries heat between the tube wall and the air or gas flowing over it. Fins are made from carbon steel, stainless steel, aluminium or copper, and are either welded or tension wound onto the tube. Helical finned tubes are used in power generation, petrochemical and chemical plants, refineries, and heating and cooling equipment.
Helical Fin Tube Types
Helical solid finned tubes
Helical serrated finned tubes
Helically wound high fin tubes
Anti-corrosive high fin tubes
Wire wound fin tubes
Spiral crimped finned tubes
Solid vs Serrated Helical Fins
| Solid fin | Serrated fin | |
|---|---|---|
|
Fin shape |
Continuous strip |
Strip cut into segments |
|
Heat transfer |
Good |
Higher (more turbulence) |
|
Pressure drop |
Lower |
Slightly higher |
|
Fouling |
Easier to clean; suits dirty gas |
Better for clean gas |
|
Typical use |
Fired heaters, economizers |
HRSGs, waste heat recovery |
Materials of Helical Finned Tubes
| Part | Materials |
|---|---|
|
Base tube |
Carbon steel (ASTM A106, A179, A192, A210), alloy steel (A213 T5, T11, T22, T91), stainless steel (304, 316, 409), copper, cupro-nickel |
|
Fin |
Carbon steel, stainless steel (409, 304, 316), aluminium, copper |
See fin tubes by material: carbon steel, alloy steel, stainless steel, copper, aluminium.
Applications of Helical Fin Tubes
- Heat recovery steam generators (HRSG finned tubes)
- Boiler economizers and air preheaters
- Fired heater convection sections
- Air-cooled heat exchangers in refineries and gas plants
- Gas compressor intercoolers and aftercoolers
- Waste heat recovery from furnaces and kilns
- HVAC heating and cooling coils
Send us the fin type, base tube material and size, fin height, thickness, fins per inch or metre, length and quantity for a quote.
FAQs – Helical Fin Tubes
What is a helical fin tube?
A tube with a fin strip wound in a continuous spiral around its outside surface. The fin multiplies the outer surface area, so far more heat moves between the fluid inside and the air or gas outside.
What is the difference between solid and serrated helical fins?
A solid fin is one continuous strip. A serrated fin is cut into segments, which breaks up the gas flow, increases turbulence and transfers more heat, at the cost of a slightly higher pressure drop.
Are helical fins welded or wound on?
Both. Solid and serrated steel fins are welded to the tube by high-frequency resistance welding. High fin, anti-corrosive and wire wound types are tension wound, and crimped fins are wound with a crimped foot.
Where are helical fin tubes used?
Heat recovery steam generators, economizers, fired heaters, air-cooled heat exchangers, gas and compressor coolers, and HVAC coils.
